RS-232 default settings
The following are factory-default data strings. RS-232 Default settings provides the RS-232 default settings.
MetSENS200
NODE, DIR, SPEED, CDIR, VOLT, STATUS, CHECK
┐Q,021,000.01,090,+05.1,0000,└ 36
Where,
| ┐: | STX (Start of String character; ASCII value 2) |
|
Q: |
Node letter |
|
021: |
Wind direction |
| 000.01: | Wind speed |
|
090 |
Corrected direction |
|
+05.1 |
Supply voltage |
|
0000 |
Status |
| └ | ETX (End of String character; ASCII value 3) |
|
36 |
Checksum (2 digit Hex Checksum sum figure calculated from the Exclusive OR of the bytes between, and not including, the STX and ETX characters) |
MetSENS300
NODE, PRESS, RH, TEMP, DEWPOINT, VOLT, STATUS, CHECK
┐Q, 1015.3,041,+022.0,+008.5,+05.1,0000,└ 36
Where,
| ┐: | STX (Start of String character; ASCII value 2) |
|
Q: |
Node letter |
|
1015.3: |
Pressure |
| 041: | Relative humidity |
| +022.0: | Temperature |
| +008.5: | Dewpoint |
|
+05.1 |
Supply voltage |
|
0000 |
Status |
| └ | ETX (End of String character; ASCII value 3) |
|
36 |
Checksum (2 digit Hex Checksum sum figure calculated from the Exclusive OR of the bytes between, and not including, the STX and ETX characters) |
MetSENS500
NODE, DIR,SPEED, CDIR, PRESS, RH, TEMP, DEWPOINT, VOLT, STATUS, CHECK
┐Q,021,000.01,090,1015.3,041,+022.0,+008.5,+05.1,0004,└ 36
Where,
| ┐: | STX (Start of String character; ASCII value 2) |
| Q: | Node letter |
| 021: | Wind direction |
| 000.01: | Wind speed |
| 090: | Corrected direction |
| 1015.3: | Pressure |
| 041: | Relative humidity |
| +022.0: | Temperature |
| +008.5: | Dewpoint |
| +05.1: | Supply voltage |
| 0004: | Status |
| └: | ETX (End of String character; ASCII value 3) |
| 36: | Checksum (2 digit Hex Checksum sum figure calculated from the Exclusive OR of the bytes between, and not including, the STX and ETX characters) |
MetSENS550/MetSENS600
NODE, DIR, SPEED, CDIR, PRESS, RH, TEMP, DEWPOINT, TOTAL PRECIP, PRECIP INTENSITY,
VOLT, STATUS, CHECK
┐Q,021,000.01,090,1015.3,041,+022.0,+008.5, 00000.200,000.200,+05.1,0004,└ 36
Where,
| ┐: | STX (Start of String character; ASCII value 2) |
| Q: | Node letter |
| 021: | Wind direction |
| 000.01: | Wind speed |
| 090: | Corrected direction |
| 1015.3: | Pressure |
| 041: | Relative humidity |
| +022.0: | Temperature |
| 0000.200: | Precipitation total |
| 000.200: | Precipitation intensity |
| +05.1 | Supply voltage |
| 0004 | Status |
| └ | ETX (End of String character; ASCII value 3) |
| 36 | Checksum (2 digit Hex Checksum sum figure calculated from the Exclusive OR of the bytes between, and not including, the STX and ETX characters) |
|
Setting |
Setting |
Setting |
|---|---|---|
| PROTOCOL: GILL | AVGLONG: 101 | SENSOR PRECIP: ON3 |
| COMMS: RS232 | SENSOR COMPASS: ON1 | UNITS PRECIP: MM3 |
| BAUD: 9600 | COMPASSDECL: +000.01 | POWER: 0 |
| NODE: Q | SENSOR TEMP: ON2 | PUPMSG STATUS: ON |
| OUTFREQ: 1Hz | UNITS TEMP: C2 | PUPMSG REPORT: ON |
| MSGMODE: CONT | SENSOR DEWPOINT: ON2 | PUPMSG UNITS: ON |
| ASCTERM: CRLF | UNITS DEWPOINT: C2 | MODBUS: RTU |
| ECHO : ON | SENSOR PRESS: ON2 | MODADDR: 1 |
| ALIGN: 01 | UNITS PRESS: HPA2 | DATABITS: 8 |
| SENSOR WIND: ON1 | HASL: +00000.002 | STOPBITS: 1 |
| UNITS WIND: MS1 | HASTN: +00000.002 | PARITY: NONE |
| NODIR: 0.001 | SENSOR RH: ON2 | MODTERM: 10 |
| AVGSHORT: 601 | UNITS RH: %2 | MODICT: 1000 |